#Center of mass finder img how to

Note that elimination of parameters by linear regression does not take place for user-defined functions.

User defined functions with up to six parameters are also possible by choosing *User-defined*. Several built-in functions are available ( see CurveFitterвЂ™s built-in functionsв†“). The function to be fit is selected from the drop-down menu.Values may be separated by spaces, tabs, commas or semicolons. Tabular data is entered or copied in the input window or alternatively, a two column text file is opened by clicking on the Open button.The typical usage of this command is listed below: On the newly obtained plot, select List, Copy or Save (these commands are described in Plot Profile в†‘) to export the curve coordinates into a spreadsheet application.With the line still highlighted by the threshold widget, run Analyze в–·Tools в–· Analyze Line Graphв†‘ to get the XY coordinates of the traced line (you can hold down Alt while selecting the command to reveal the actual image that is processed ).Select the curve with the Wand Toolв†‘ and run Edit в–· Clear Outsideв†‘ to erase everything on the canvas but the curve.Open the ThresholdвЂ¦В в†‘ tool ( Shift T) and adjust the threshold levels so that the curve is highlighted in red.Alternatively, use one of the drawing tools ( Pencilв†‘ or Brushв†‘) to paint directly in background color. Use any of the Area Selection Toolsв†‘ as an eraser (press Backspace to erase) in order to isolate the single graph curve to be measured. Set background color to white using the Color Picker Toolв†‘ or the Color Picker windowв†‘.Analyze Line Graph will assume that the graph is displayed on a white background so images with darker backgrounds must be adjusted beforehand ( see e.g., Edit в–· Invert в†‘ and Process в–·Binary в–· Make Binaryв†‘). Make sure your graph is a grayscale image ( Image в–· Type в–·в†‘8-bit). For practice, use the File в–· Open Samples в–·в†‘Line Graph (21K) sample image.

#Center of mass finder img how to

The following procedure describes how to use it: This command uses the Particle Analyzerв†‘ to extract sets of coordinate data from digitized line graphs. Select Gels в–·в†‘Label Peaks to label each measured peak with its size as a percent of the total size of the measured peaks.If necessary, scroll the image vertically by holding down the space bar and dragging. For each peak, measure the size by clicking inside the peak with the Wand Toolв†‘.

To access to all the lanes, it may be necessary to scroll the image vertically using the Scrolling Toolв†‘ (Hold down the space bar to temporarily switch to this tool). Note that you can hold Shift to constrain lines to be either horizontal or vertical.

Use the Straight Line Selection Toolв†‘ to draw base lines and/or drop lines so that each peak of interest defines a closed area (ImageJ will automatically switch to the Straight Line tool).

Select Gels в–·в†‘Plot Lanes ( 3вЂ‰) to generate the lane profile plots.

Repeat the previous step for each remaining lane.

The selected lane is outlined and labelled, and вЂLane n selectedвЂ™ is displayed in the status bar.

Move the rectangular selection right to the next lane (or down if the lanes are horizontal) and select Gels в–·в†‘Select Next Lane ( 2вЂ‰).

Select Gels в–·в†‘Select First Lane ( 1вЂ‰) and the lane will be outlined and вЂLane 1 selectedвЂ™ displayed in the status bar.

This should be the left most lane if the lanes are vertical or the top lane if the lanes are horizontal.

Use the rectangular selection tool to outline the first lane.

Note that a copy of the gel image with the lane outlines can be created at any point using the Image в–·Overlay в–· Flatten в†‘ command. For practice, refer to the video tutorial on the ImageJ wikipage and use the File в–· Open Samples в–·в†‘Gel sample image (1-D gel) to perform the following steps.